Cordless drill driver driving a screw into a timber beam in a workshop

Impact Driver vs Drill vs Impact Wrench: Which Cordless Tool Do You Need?

LanguageEnglishالعربية

Short answer: choose by the fastener, not by the torque number. A drill driver has a 13 mm chuck and a slip clutch, so it drills holes in wood and metal and drives small screws without stripping them. An impact driver has a 1/4 in hex collet and hammers the bit round in short pulses, so it sinks long screws and lag bolts fast with no kick on your wrist, but it has no clutch and no chuck. An impact wrench has a 1/2 in square drive for sockets and is built for nuts and bolts: wheel nuts, anchor bolts, steel frames. If you are buying one tool for the house or the shop, buy the drill driver (or the hammer version, the impact drill, if you also drill into block walls). Buy the impact driver second, once you drive screws by the box. Buy the impact wrench only if you work on cars, steel or anchors.

The rest of this guide explains the differences with INGCO's own published figures, why a 66 Nm drill and a 230 Nm impact driver are not the same kind of number, and when each tool is the wrong choice.

Cordless drill driver driving a screw into a timber beam in a workshop
A drill driver does both jobs most people buy a cordless tool for: holes and small screws.

In this article

What is the difference between a drill driver, an impact driver and an impact wrench?

All three are 20 V cordless tools that spin a fastener. They differ in what they hold, how they deliver torque, and how much control they give you. The table uses the figures INGCO publishes for three 20 V P20S models the store stocks.

Drill driver Impact driver Impact wrench
What holds the bit 13 mm keyless chuck, takes any round or hex shank 1/4 in (6.35 mm) hex collet, hex-shank bits only 1/2 in square drive, impact sockets only
How it turns Steady rotation through a gearbox Rotation plus rotational hammer blows (impacts per minute) Rotation plus heavier rotational hammer blows
Torque control Clutch, 22 settings plus drill on the CDLI20668 None, you feather the trigger None, usually 3 speed modes
INGCO figure Max torque 66 Nm (CDLI20668) Max torque 230 Nm (CIRLI2023) Fastening torque 400 Nm (CIWLI2040)
No-load speed 0 to 500 / 0 to 2,000 rpm 0 to 2,000 / 2,400 / 2,600 rpm 0 to 1,600 / 1,900 / 2,300 rpm
Impact rate None 0 to 2,100 / 2,500 / 2,900 bpm 0 to 2,100 / 2,500 / 2,900 bpm
Best at Drilling holes, small and medium screws, anything delicate Long screws, coach screws, self-drilling screws in quantity Nuts and bolts, wheel nuts, anchor bolts, steel assembly
Store price, kit with 2 batteries $84.00 $95.50 $103.50

Two things in that table decide most purchases. First, the chuck: only the drill driver holds an ordinary round-shank drill bit. Second, the clutch: only the drill driver will stop turning when the screw is seated, which is why it is the tool for cabinet hinges, socket boxes and plasterboard.

INGCO Cordless Drill 20V Brushless 66 Nm CDLI20668
Drill driver
INGCO Cordless Drill 20V Brushless 66 Nm CDLI20668

13 mm metal chuck, 22+1 clutch settings, two speeds, two 2.0 Ah batteries, charger and 47 accessories. The one tool that drills and drives.

$84.00View product

Why is an impact drill not an impact driver?

This is the naming trap that causes most wrong orders. INGCO, like many brands, calls its hammer drill an impact drill. On the store it is the مقدح رجراج: a drill driver with a 13 mm chuck, a clutch, and a third mode that hammers forward, along the bit, about 30,000 blows a minute on the CIDLI20558. That forward hammering is for masonry: it lets a carbide bit chew into brick, block and render.

An impact driver (the وز or فرد شد براغي in the trade) hammers sideways, around the axis. A spring-loaded hammer inside strikes an anvil in the direction of rotation, roughly 2,900 times a minute on the CIRLI2023. Each strike adds a burst of twist to the bit. That is why it drives a 120 mm screw that would stall a drill, and why your wrist feels almost nothing: the torque arrives in pulses too short to twist the tool out of your hand.

An impact wrench (فرد شد عزق) uses the same sideways hammer mechanism, scaled up, behind a square anvil for sockets. So when you search "impact", be clear which of the three you mean: forward blows for concrete, rotational blows for screws, rotational blows for bolts.

Can you compare 66 Nm with 230 Nm and 400 Nm?

Not directly, and this is where buyers get misled. A drill driver's rating is the steady twisting force its gearbox and clutch deliver, so 66 Nm means the chuck can push a bit with up to 66 Nm continuously. An impact tool's rating is the peak torque delivered during the hammer blows. The motor itself never produces 230 Nm; the hammer and anvil do, in bursts. Pro Tool Reviews also points out that many impact wrench makers advertise "nut-busting" (loosening) torque, which is higher than the fastening torque, so check which one is quoted. INGCO publishes fastening torque for the CIWLI2040, 400 Nm, which is the useful number.

The practical consequences:

  • A 230 Nm impact driver cannot be dialled down to 2 Nm. Drive a 3.5 mm screw into a hinge with it and you will strip the head or split the timber. Use the drill driver's clutch for that.
  • A 66 Nm drill will stall and kick on a long coach screw. That reaction torque is what twists your wrist; the impact driver has almost none.
  • A 400 Nm wrench on a small bolt will shear it. Impact wrenches are for M10 and up, and for things that were tightened by a machine in the first place.
Drill bits and small screws, long screws, and hex bolts with nuts laid out on a workbench
Left to right: what the drill driver, the impact driver and the impact wrench are each built for.

When should you choose an impact driver over a drill?

Choose the impact driver when the job is screws by the box rather than screws by the handful: decking and pergola screws, 80 mm and longer, plasterboard batten screws into steel studs, self-drilling tek screws into sheet metal, coach screws and frame anchors, and assembling pallets or crates. It is shorter and lighter than a drill, and the collet never lets a bit slip under load.

Three things to know before you buy one:

  • Bits must be impact rated. Ordinary chrome-vanadium bits snap under rotational hammering. Impact bits are made from tougher S2 steel with a torsion zone; the store's 31-piece impact bit set is $10.50.
  • It drills, but badly. With a hex-shank bit it will make a pilot hole in timber. It will not drill a clean 10 mm hole in steel, and it cannot take a masonry bit for block walls.
  • Speed modes are your only control. The CIRLI2023 has three: 2,000, 2,400 and 2,600 rpm. Start on the lowest for anything you have not driven before.
INGCO Cordless Impact Driver 20V Brushless 230 Nm CIRLI2023
Impact driver
INGCO Cordless Impact Driver 20V Brushless 230 Nm CIRLI2023

1/4 in hex collet, three speed modes up to 2,600 rpm and 2,900 bpm, two 2.0 Ah batteries and charger. For long screws in quantity.

$95.50View product

If you also want a hammer drill for the occasional hole in a block wall, the CKLI20277 combo pairs the 66 Nm impact drill with an impact driver on the same two batteries for $136.00, which is less than the two kits bought separately.

When do you need an impact wrench?

You need an impact wrench when the fastener is a nut or a bolt head, not a screw, and when it was tightened hard. That means changing car wheels, loosening suspension and exhaust bolts, driving M12 and M16 anchor bolts for machines, racks and solar structures, and bolting steel frames and scaffolding. Car makers specify wheel nuts somewhere around 100 to 150 Nm depending on the model, so a 400 Nm class tool like the CIWLI2040 removes them without effort. For trucks, agricultural machinery and seized bolts the store also carries the 850 Nm CIWLI2085.

Two rules apply to every impact wrench:

  • Impact sockets only. Chrome hand sockets are hard and brittle; under hammering they crack and can shatter. Wright Tool's safety guidance is blunt about it: chrome adapters should never be used with power tools. Use the black impact sockets, such as the store's 10-piece 1/2 in impact socket set at $16.25.
  • Finish wheel nuts with a torque wrench. An impact wrench loosens and runs nuts down; it does not know when 120 Nm has been reached. Over-tightened wheel nuts stretch studs and warp brake discs. Run them down with the impact wrench, then set the final torque by hand.
INGCO Cordless Impact Wrench 20V Brushless 400 Nm 1/2 in CIWLI2040
Impact wrench
INGCO Cordless Impact Wrench 20V Brushless 400 Nm 1/2 in CIWLI2040

1/2 in square drive, 400 Nm fastening torque, three speed modes, two 2.0 Ah batteries and charger. For wheel nuts, anchor bolts and steel.

$103.50View product

When is each tool the wrong choice?

The impact driver is wrong for anything with a small or soft screw: kitchen hinges, socket and switch plates, electronics, hardwood furniture where a split is a disaster. It is also wrong as your only drill. Every combo kit in the catalogue pairs it with a drill for exactly that reason.

The impact wrench is wrong for screws of any kind, for small bolts under M10, and for the final tightening of anything with a specified torque. It is heavy and loud, and with an adapter and a hex bit it makes a poor impact driver: the hammer mechanism is sized for bolts and will snap bits and strip screw heads.

The drill driver is wrong for hundreds of long screws in a day (your wrist will tell you by lunchtime), for lag bolts and coach screws above about 8 mm, and for concrete. For drilling anchors into concrete columns and slabs you need a rotary hammer, not any of the three tools here; our impact drill vs rotary hammer guide explains why joules matter more than watts there.

One more honest note: a 400 Nm cordless wrench is a compact class tool. Seized truck wheel nuts may need the 850 Nm or 1,350 Nm models, or a breaker bar first.

Which kit should you buy first?

All the tools in this guide run on INGCO's P20S battery, so the sensible path is one kit with two batteries, then bare tools after that. The CDLI20668 drill driver kit at $84.00 comes with two 2.0 Ah packs and a charger; a spare 2.0 Ah battery is $17.95. Once you own batteries, the bare 55 Nm drill is $25.95 and the bare 400 Nm impact wrench is $46.95, less than half the kit price.

For a tradesperson starting out, the combo below covers screws and masonry in one box.

INGCO Impact Drill 66 Nm + Impact Driver Combo Kit 20V CKLI20277
Combo kit
INGCO Impact Drill 66 Nm + Impact Driver Combo Kit 20V CKLI20277

A brushless 13 mm impact drill with clutch and hammer mode, plus a brushless impact driver, two 2.0 Ah batteries, charger and case.

Frequently asked questions

Can an impact driver replace a drill?

No. It has no chuck for round-shank bits, no clutch for small screws, and no hammer mode for masonry. It is the second tool, bought to take the long screws off your drill.

Can I use normal screwdriver bits in an impact driver?

You can fit them, but they break. Use impact-rated bits, which are made from tougher steel with a flexible torsion zone. The CIRLI2023 ships with two bits; a full set like the AKSD68303 costs $10.50.

Can I use chrome sockets on an impact wrench?

No. Chrome sockets and adapters are hardened for hand use and can shatter under impact blows. Use black impact sockets and impact-rated adapters only.

Is 230 Nm on an impact driver more than 66 Nm on a drill?

The numbers are measured differently. 66 Nm is the drill's continuous torque through a clutch; 230 Nm is the impact driver's peak torque during hammer blows. The impact driver drives far longer screws, but it cannot be set to a low torque the way the drill can.

Which one tightens wheel nuts?

The impact wrench, with a 1/2 in impact socket. Use it to loosen and to run the nuts down, then finish with a torque wrench to the figure in your car's handbook.

Do all three use the same battery?

Yes. The models in this guide are all INGCO P20S 20 V tools and share the FBLI20011 2.0 Ah, FBLI20021 4.0 Ah and FBLI20031 5.0 Ah packs.

Not sure which one your work needs?

Send us a photo of the fasteners you drive most and we will tell you which tool, and which bits or sockets, to order.

Browse INGCO cordless tools

Cash on delivery, five day returns, fast delivery. Call or WhatsApp +961 76 10 17 18.

Back to blog